Cascadia
- Update Instructions
- Changelog
- Turn off power to Cascadia.
- Remove any speakers or headphones to avoid unwanted sounds, or loud noises.
- Connect a USB cable from the rear of Cascadia to your computer.
- From the version menu above, select the firmware version you will be updating to.
- Hold down the MIDI PITCH button on the panel and turn on power.
- Click the Update button in the bottom of this window. You will see the progress of the update in the
log window and your module may begin to flash. You will see an “Update completed successfully” message at
the end of the update.
- Turn Cascadia off and back on again, you're now ready to go.
- If there are any problems please contact us via the Help button on our website. Be sure to include the full
log window output, the firmware updater version downloaded, and the OS you are using.
1.4.1.0 (2024-03-13)
- NEW: MPE Member Channel support, configure with Config App 1.6.1+.
1.4.0.0 (2024-02-28)
- NEW: MPE Support!
- CC74 (MPE Y/Timbre) and Pressure (MPE Z) are learnable and output from the active note.
- MPE mode maintains it's own Pitch Bend Range setting with a default of 48.
- Supports the new Albeton Live 12 tuning system.
- Supports Lower and Upper Zone.
- Setup everything using the updated Intellijel Config App 1.6 or higher.
- NEW: Pressure Curve and Threshold settings. Applies to Mono/MPE Modes.
- TWEAK: Pitch Bend Range (Sensitivity) max increased from 24 to 96.
- TWEAK: Note stack increased from 8 to 15. (Max number of held keys)
- Updated manual and Config App (1.6.0.0 or higher required) available at intellijel.com/support.
1.3.1.0 (2024-01-16)
- FIXED: MIDI Portamento (CC# 5 and 65) was not responding in certain configurations.
1.3.0.0 (2023-12-19)
- NEW: Dual Mono MIDI Mode — Add a 2nd MIDI Pitch and Gate.
- Hold down MIDI CC button on boot to Toggle ON/OFF (or use IntellijelConfig.App 1.5+)
- Tap the MIDI CC button to learn the MIDI channel for the 2nd voice.
- CC = Pitch 2
- MOD = Gate 2
- Additional coarse tuning/pitchbend options available in the IntellijelConfig.App.
- NEW: Option Env B LFO Mode called the ESG (Entropic Sequence Generator).
- Hold down MIDI LFO button on boot to Toggle ON/OFF (or use IntellijelConfig.App 1.5+)
- It will replace the Tilt Triangle LFO on Env B. See the Manual for details.
- RISE = Rate.
- FALL = Sequence length (1 to 16 stages).
- SHAPE = Step regeneration probability (0% to 100%).
- In LFO-SYNC Mode, the SYNC input will set the base rate.
- In LFO-FREE Mode, the SYNC input will Reset the Sequencer.
- Updated manual and Config App (1.5.0.0 or higher required) available at intellijel.com/support.
1.2.6.0 (2023-10-13)
- TWEAK: Extended the assignable CCs available to the full range, 0-127.
- Config App (1.4.3.0 or higher required) available at intellijel.com/support.
1.2.5.0 (2023-09-20)
- FIXED: USB MIDI lag that may occur with lots of MIDI traffic.
- FIXED: ADSR could retrig multiple times per trig at the shortest attack time.
1.2.4.2 (2023-05-24)
- TWEAK: Hold MIDI CLK on boot to Reset Settings, now flashes Sync LED and updates Tap Tempo.
- FIXED: Saved Tap Tempo period now carries over to new version.
1.2.4.0 (2023-05-24)
- FIXED: Tap Clock MIDI output on MIDI OUT (DIN) connection restored.
- FIXED: Removed extreme slew on MIDI CC and MOD Outputs.
- TWEAK: Better handling of MIDI GATE Output for touching (not overlapping) MIDI notes.
- TWEAK: Faster boot time.
1.2.0.3 (2023-05-09)
- FIXED: Intermittent USB MIDI messages.
1.2.0.2 (2023-05-08)
- NEW: New MIDI LFO shape: "Random Notes" added to the list of LFO shapes available at the MIDI LFO output.
Random Notes outputs clocked random voltages, which are quantized to semitones. You can constrain the octave
distribution by using the new LFO Level and LFO Polarity options in the Intellijel Config app's MIDI LFO
section (see below).
- NEW: LFO Level parameter in the Intellijel Config App's MIDI LFO section. This sets the maximum output
voltage (amplitude) of the MIDI LFO to either 1V, 2V, 3V, 4V or 5V (the default). NOTE: This parameter
is only available via the Intellijel Config app, and can not be set on the front panel.
- NEW: LFO Polarity parameter in the Intellijel Config App's MIDI LFO section. This selects whether the MIDI
LFO is Unipolar or Bipolar (the default). When set to Bipolar mode, the LFO output ranges between the
negative and positive voltage set by the LFO Level parameter. NOTE: This parameter is only available via
the Intellijel Config app, and can not be set on the front panel.
- NEW: Support for MIDI Portamento mode. Specifically, CC 65 (Portamento Control) on Cascadia's MIDI Channel
turns portamento ON (value = 127) or OFF (value = 0). Sending CC 5 (Portamento Time MSB) on Cascadia's MIDI
Channel sets the portamento time from 0 seconds (CC 5 = 0) to about 1.1 seconds (CC 5 = 127), slewing the
pitch.
- Minor bug fixes and performance enhancements.
- Updated manual and Config App (1.4.1.0 or higher required) available at intellijel.com/support.
1.1.0.0